How To Measure For A Screen Window

Download Article

Download Article

A screen spline is a safety cord that keeps the window screen secure in its frame. If you've purchased a new window or your former spline is damaged, yous'll need to purchase a new screen spline. Have measurements of the sometime spline or the window frame groove to make sure you purchase the right spline size. All you need to know is the spline bore and width!

1. ane

   Remove the screen frame from the window. Check for clips property your window screen in and, if you spot any, elevator the clips up to unfasten the screen from the window. In nigh cases, your window screen frame should pop out easily.^[1]

   • If your screen frame is secured past clips, they should be located along the left and right sides.
   • Later removing the frame, lay information technology down on a flat surface similar a table.

2. ii

   Use a flat-head screwdriver to pry the screen spline up. Have the screwdriver and pry up 1 stop of the screen spline. Lift information technology until you can grab the terminate of the screen spline with your easily.^[2]

   • Y'all can pry the screen spline up from either end.
   • If you don't have a flat-caput screwdriver, you tin can use a butter knife as an culling.
   • The screen spline looks similar a long string made of prophylactic or cream.^[3]

   Advertisement

3. three

   Pull the screen spline upwards and out of the frame. One time yous take a strong grip, pull upward on the screen spline with lite force per unit area. Continue lifting the spline until you remove information technology from the window frame completely.^[4]

4. 4

   Endeavour non to damage the screen spline as you remove it. You will get the best and most precise readings if you go along the screen spline as intact as possible. If the spline is already broken, remove it gently to keep it as intact as you tin can.^[5]

Advertising

1. ane

   Use the one-time spline as a guide for new spline measurements. Do not throw abroad your screen spline if it was recently damaged. Y'all tin withal use it to determine the size your new screen spline should exist.^[6]

2. 2

   Use a tape measure to notice the bore of your spline if information technology's intact. Lay the screen spline on a apartment surface and position the tape measure across 1 end of the spline to find the diameter, or width, of the spline.^[7] Mensurate from 1 side of the spline to the other, and write down the number.^[8]

   • The spline's measurements tend to exist in inches or centimeters, depending on whether your country uses the majestic or metric measurement organisation.

3. 3

   Mensurate the spline groove opening's bore as an alternative. If your screen spline is badly damaged or you no longer take it, you can use the screen frame to take the spline bore. Place the tape mensurate inside the spline groove opening and have measurements from the lesser of the opening to the summit to find the diameter.^[nine]

   • The spline groove opening is the place in the screen frame where yous insert the spline.

4. iv

   Buy a new spline with the same measurement. Try to find as precise a match equally possible.^[ten] If your spline measurements are between 2 sizes, make up one's mind whether the width is nearer to the larger or smaller size and choose the closest match.

   • If you old spline has a .125 in (0.32 cm) bore, for example, yous would await for a new spline with the aforementioned measurements on the bundle.

Advertisement

1. 1

   Cut the new spline to size. Mensurate all 4 interior sides of the screen with a tape mensurate and record the length. Use scissors or a sharp knife to cut your spline to the same length.^[xi]

   • If your previous spline's length is still intact, use it every bit an additional guideline while cutting the spline to size.

2. 2

   Press the spline into identify. Starting in 1 corner of the screen, employ your hands to insert the spline into the frame groove. Use a spline roller to smooth over any raised areas to make sure information technology stays secure.^[12]

3. three

   Troubleshoot problems with lubricant or by stretching the spline. If the spline does not hands lay flat in the frame groove, endeavor spraying it with a silicone lubricant, available at hardware stores.^[13]

   • If the spline is too large to insert into the screen, pull on 1 finish to stretch it thinner equally you insert it. The spline should return to its original shape and continue a firm hold in the frame.

Advertisement

Add New Question

• Question

  How exercise I know what size replacement screen spline to buy?

  

  Michael Fox is a Window Repair Specialist and the President at Window Repair Systems and WindowHardwareDirect.com, based in Westminster, South Carolina. With over 25 years of experience, Michael specializes in commercial window repair and service. He holds a business degree from Monroe Community College and SUNY Brockport. Michael has helped Window Repair Systems and WindowHardwareDirect.com become an industry leader in commercial window repair and hardware distribution, servicing schools and businesses and grooming big public school systems.

  

  Window Repair Specialist

  Expert Answer

Ask a Question

200 characters left

Include your e-mail address to become a message when this question is answered.

Submit

Ad

• Spline sizes are shown in decimals on the packaging. If you lot wrote the size in fractions, convert it to decimals before shopping for a screen spline.

Advertising

Things Y'all'll Need

• Tape measure
• Screen spline
• Flat-head screwdriver
• Scissors
• Spline roller (optional)
• Silicone lubricant (optional)

About This Article

Article Summary X

If the cord that keeps your window screen in its frame is cleaved, you lot'll demand to get a new screen spline. To measure your screen spline, kickoff by removing the screen frame from the window. Use a flat-caput screwdriver to pry the screen spline up and out of the frame. Lay the screen spline on a flat surface and position your tape measure beyond one end to find the bore, or width. Buy a new spline with the aforementioned measurement. If your new spline is longer than what you need, simply cutting it down to the proper size with scissors or a sharp knife. You can and so press the spline into the frame groove and use a spline roller to shine over whatsoever raised areas. To learn how to accommodate your spline to brand sure it fits your screen properly, keep reading!

Did this summary help you?

Thank you to all authors for creating a page that has been read 52,733 times.

Did this article help you lot?

Source: https://www.wikihow.com/Measure-a-Screen-Spline

Posted by: adamsmeman1981.blogspot.com

Share this post