How Do I Get The Screws Out Of My Shark Duo Clean

For this tutorial, we'll look at how to remove the roller brush from a Shark Duo Make clean nozzle.

Cleaning the brush curlicue is an integral part of keeping whatsoever Shark vacuum running its best.

The Duo Clean is perhaps my favorite tool for cleaning hard floors considering of its efficiency and the bright LED headlights that aid a great deal in tracking dust.

Still, one issue with the Duo Clean nozzle, at least the earlier ones without Zero-M, is hair wrapping around the brush roll.

It won't wrap on the roller, but on the castor backside information technology, so information technology'due south essential to remove whatsoever pilus and other stuff that may impede airflow.

I'll be demonstrating the steps using the Shark ION P50 cordless stick vacuum.

Steps for other models may vary, then use the data yous see hither as a guide.

How to remove and clean roller castor from Shark ION P50

Removing the roller from the ION P50 is a uncomplicated process, and you'll need one tool – a coin broad plenty to remove the 3 bolds underneath.

Step ane: Detach the Main Nozzle

The first step is separating the tube from the frame past pushing a button (check photo) to release the lock.

Afterwards removing the tube, printing the latch over the grit container to remove it from the frame.

These steps remove most of the bulk away from the nozzle, so it's easier to clean.

Stride 2: Removing the Roller Brush

In the ION P50, there is a release latch on one side of it with an "eject roller" written. Gently push it frontward to release the roller.

Make certain to have the nozzle low to the ground or accept another hand to catch it, so it doesn't driblet to the ground. Once yous push the lever, the roller pops out. It'due south something to keep in mind.

In one case you accept the roller out, it's easier to make clean.

Shark recommends only using h2o to wash the roller and drying thoroughly before returning it to the vacuum.

Stride 3: Remove 3 bolts

For the ION P50, cleaning the roller volition be easy since it pops out. However, the castor behind it does not. So yous'll have to remove the plate by unfastening three bolts.

You could use a flathead screw, just a coin with enough width should do the task.

Afterward removing the castor baby-sit, you'll have more than space to remove any pilus using pair of scissors and other debris clinging to it.

There are grooves across the brush, which makes this task easier.

Step 4: Cleaning Other Areas of the Nozzle

You'll also detect dust and other contaminants sticking on the various nooks and crannies. 1 efficient way to clean these areas is by using a handheld vacuum with a brush attachment.

For this demonstration, I'm using the Roborock H6 stick vacuum. It comes with a brush attachment that's excellent for this task.

Brand sure to make clean the ii big wheels behind the brushes since dirt will stick on it and source of scratches on hardwood floors.

Don't forget to check the small wheels at the sides of the guard as dirt can build upward in these areas. Yous can use a damp fabric to tidy up these parts and to remove whatever contaminant or pilus.

Pace v: Reattach Castor Guard

After cleaning the brush, reattach the brush guard and bolt on the three fasteners. Don't overtighten it as it easily strips since it's a plastic part.

Stride 6: Reattach the Roller Bar

Next is attaching the soft roller bar and locking information technology in place. The roller simply goes in a specific direction, so it's pretty idiot-proof.

Step vii: Attach the tube.

The last step is to reattach the tube on the frame in its upright configuration.

Note that removing the roller on other models like the Shark APEX and NV-800 series. Most of them volition have squirt buttons that push it out.

Source: https://www.bestcordlessvacuumguide.com/how-to-remove-roller-brush-from-shark-duo-clean/

Posted by: adamsmeman1981.blogspot.com

Share this post